RFID Access Control 125khz

How to program or Add RFID card or medal ?

1-     Enter programming mode : click '*' + programming-password (1234 is default ) + '#'.

2-     self-numbered card issuing method: operation method: click ‘2’ ‘1’ + # + read card + 3 digits self-numbering code  then wait about 10 seconds

       or quick add card: operation method: input 2 “ 0 + # + read card

note: you can read multiple cards at the same time to add cards. if you stop in the card for 10 seconds, the program will automatically exit the management state.

 How to Delete a Card or Medal ?

1-     Enter programming mode : click '*' + programming-password (1234 is default ) + '#'.

2-     swipe card deletion method: operation method: enter 3 0 + # + read card

note: this method can read multiple registered cards at the same time for deletion. if you stop in the card for 10 seconds, the program will automatically exit management status.

 

How to Restore Factory Defaults?

1-     Enter programming mode : click '*' + programming-password (1234 is default ) + '#'.

2-     restore the factory default to restore the factory default: operation method: enter “7” “0” + “#” note: all parameters are automatically restored to the factory default values after the command is input. (delete all cards, restore all parameters, restore management password: 1234)

 

How to change Management Password ?

1-     Enter programming mode : click '*' + programming-password (1234 is default ) + '#'.

2-     to change the administrator password:
enter "6" "0" + "#" + 4-8 digits new administrator password + "#" + repeat 4-8 digits new administrator password + "#"

 

How to add a password number to open lock or door without RFID Card ?

1-     Enter programming mode : click '*' + programming-password (1234 is default ) + '#'.

2-     click “ 1 ” “ 1 ” + “ # ” + 4-8 digits to open the door + ‘#’ + wait about 10 seconds

 

now, any time you can write your password + ‘#’ to open the lock or door.

 

to delete a single password:

1-     Enter programming mode : click '*' + programming-password (1234 is default ) + '#'.

2-      Click "3" "5" + "#" + open password + " # "

Detailed Instructions :-

press and hold the reset button, wait for 2 seconds to hear the tone (drop) and release, the access control will restore the management password to the factory default (1234), if you continue to hold reset for 5 seconds, you will hear the initialization tone (drop. after the drop: drop), the reset button can be disconnected, and the access control is automatically initialized until the end of the door is issued. initialize the device, all card data, management password, etc.

divide or revert to factory defaults. (delete all cards, restore all parameters, restore management password: 1234)

 

management status command table

 

login programming status: operation method: enter " * " + programming password + " # " default programming password: 1234 after logging in to the management state the green light ( mode ) turns solid.

 

exit management status: operation method:

 

after the input exits the management state, the green light ( mode ) turns flashing

 

note: the following commands are only valid in the administrative state. (in the management state, if there is no keyboard operation within 10 seconds, the program will automatically exit the management state)

 

card issuing password operation

 

enter the card number plus card: operation method: enter "1" "0" + "#" + 8 digit card number + "#" note: the card is printed with "0012345678 ” , you only need to input the last 8 digits 12345678 to send the card.

 

add the opening password:

 operation method input “ 1 ” “ 1 ” + “ # ” + 4-8 digits password + “ # ” + wait about 10seconds

 

note: the opening password is 4-8 bit number. up to 100 groups of opening codes can be added

anytime you can wirte the  4-8 digits password+’#’ to open the door or lock.

 

add duress password: how to do it: enter "1" "2" + "#" + 4-8 digit duress password + "#" note: duress password is only one set

 

when you add a new duress password, it overwrites the original set of passwords.

 

“ ” ” “ ”

 

quick add card: operation method: input 2 “ 0 + # + read card

note: you can read multiple cards at the same time to add cards. if you stop in the card for 10 seconds, the program will automatically exit the management state.

 

“ ” “ ” “ ”

 

self-numbered card issuing method: operation method: input 2 1 + # + read card + 3 digits self-numbering code: easy to remember, if a card is sent to room 302 (self-numbered 302), the card number corresponds to the room no., easy to remember. (one self-numbering supports multiple cards) if you need to continuously add cards with self-numbering, please enter the 3-digit self-numbering " "

after entering the # key, you can read the card and send the next card continuously. the maximum number of self-coded numbers can be added to one hundred groups.

operation method: enter “ 2 ” “ 3 ” + “ # ” + read the master card

note: master card plus card: read the master card twice in succession

 

send the operation master card: , enter the master card plus card mode, you can read the card continuously for card issuance.

 card deletion: in the non-management state, read the master card, enter the card deletion mode, read the card that needs to be deleted twice, and then read the master card for confirmation, and delete the card “ ” ” “ # ”

 

send a passcode card: how to do it: enter ‘2’  ‘4’ + ‘# ‘ + read card + enter the 4-8 digit password of the card + “ note: after entering the command, read the card and then enter the password.

 

second, delete the card to delete the password operation

 

“ ” “ ” “ ”

swipe card deletion method: operation method: enter 3 0 + # + read card

note: this method can read multiple registered cards at the same time for deletion. if you stop in the card for 10 seconds, the program will automatically exit management status.

 

card number deletion method: operation method: enter “3” “1” + “#” + 8 digit card number + “#” note that if the card is printed with “001234 self-numbered card deletion method: 5678 operation”, the method only: input input is required “3” after the 8 digits “2” + “12345678 # ” +3 digits can be deleted by the number card + . “ # ” note: after input, it corresponds to 3

 

the card from the number will be deleted.

 

to delete a single password: how to do it: enter "3" "5" + "#" + open password + " # " note: after input, delete the pair

 

open password

 

delete all passwords: how to do it: enter "3" "6" + "#" note: all passwords will be deleted. delete all open data at once: how to: enter "4" "0" note: command execution

 

afterwards, the access control will clear the data such as the opening card and the opening password, and after the cleaning is completed, an end tone will be sounded to indicate completion.

 

third, modify the parameter setting operation

 

to change the administrator password: how to do it: enter "6" "0" + "#" + 4-8 digits new administrator password + "#" + repeat 4-8 digits new administrator password + "#" note: replace when you manage your password, you need to confirm the new password twice. when you enter it,

 

the password should be consistent twice, otherwise it will not be successful. “ ” ” “ ” “ ”

 

modify the door open time reminder: operation method: input 6 “ 3 + # + 3 digits door open timeout time + # note: when entering 000, close the door open timeout reminder function. the unit is seconds. (maximum can be set 255 seconds)

 

+ ” + ” 

 

modify the alarm duration: operation method: input “6” “4” # + 3 digit alarm duration “# note: when entering 000 (default) modify the door open delay time to close: operation alarm method, : input input 255 “6, "alarm" 6 ” time + “# unrestricted” +3 digits. door opening delay time + “ # ” note: when 000 is entered, it is set to 0.5 seconds, the default is 3 seconds, and the longest is 255 seconds. detect door open password setting: operation method: input “6” “8” + “#” + 1 bit error count + 2 bit lock duration + “ # ” note: when input 999 (default), error 9 times self-locking 99 seconds .

 

4. restore the factory default to restore the factory default: operation method: enter “7” “0” + “#” note: all parameters are automatically restored to the factory default values after the command is input. (delete all cards, restore all parameters, restore management password: 1234) v. open and close commands

 

set the electric lock normally open: operation method: input “8” “3” + “#” note: after the setting is successful, the electric lock will not lock. ( also available "press and hold the door switch "5 seconds to activate this function" go: enter "8" "4" "#" note "

 

set the power: after the setting is successful, restore the default state. ( also available

 

press and hold the door switch for 5 seconds to turn off the function. operation method: enter “8” “5” + “#”

open the full card to open the door: : after turning this function on, reading all cards can open the door. turn on auto registration: how to do it: enter “8” “6” + “#” note: after turning on this function, reading all cards will open the door.

 

open the full card to open the door: : after turning this function on, reading all cards can open the door. turn on auto registration: how to do it: enter “8” “6” + “#” note: after turning on this function, reading all cards will open the door.

alignment

if it is an unregistered card, it will be registered at the same time, and then open the door. " " " " " "

close the full card to open the door: how to do it: enter 8 7 "#

turn on the anti-copy card reading: operation method: enter “8” “8” + “#” note: after the setting is successful, the system starts to block the copy card.

turn off the anti-copy card reading: operation method: enter “8” “g” + “#” note: after the setting is successful, the copy card can also open normally (default).

tips: turn on and off anti-copy function is limited to id card access control, ic card, access control does not have this function.